AI photo restoration · Pay once, no subscription

How to Scan Old Photos: The Settings That Matter

Scanning is the best way to digitise a print, and the settings are simpler than the menus suggest. Here is what to choose, why, and when to put the scanner away and use a camera instead.

Choose resolution by the size of the photo

Resolution is measured in dots per inch (dpi). The number you need depends on how small the print is and how large you want to make it later. A simple rule: multiply the dpi by the print size in inches to get the pixel dimensions. A 4x6 inch print scanned at 600 dpi gives 2400 x 3600 pixels, enough for an 8x12 inch print at 300 dpi.

OriginalScan atWhy
Wallet or very small prints1200 dpiFaces have only a few pixels otherwise
4x6 or 5x7 prints600 dpiGood balance of detail and file size
8x10 and larger300 to 400 dpiAlready plenty of pixels
35mm negatives and slides3600 dpi or moreThe frame is only about 1 inch wide

Scanning higher than the original can resolve does not add detail, only file size. Scanning at 4800 dpi a print that was soft to begin with gives you a very large, equally soft file.

Colour mode and file format

  • Scan black-and-white and sepia photos in colour (24-bit or 48-bit), not greyscale. Toning, stains and fading carry information, and you can always convert later.
  • If you plan to keep a master copy, save it as an uncompressed TIFF, and make JPEG copies for sharing. A high-quality JPEG is fine if storage is limited.
  • Name files sensibly, for example 1962-smith-wedding-front.tif, and scan the back whenever there are notes.

Turn off the "helpful" features

Many scanner programs apply automatic colour restoration, sharpening, dust removal or backlight correction. Switch them off for the master scan. These filters change the tones and invent detail in ways you cannot undo, and a later restoration is better served by a faithful copy. One exception: printed halftone material, such as a newspaper clipping or a postcard, benefits from the "descreen" option, which removes the dot pattern.

Prepare the print and the glass

  • Wipe the scanner glass with a dry microfibre cloth. Every speck on the glass becomes a spot on every scan.
  • Remove dust from the print with a soft brush or a hand blower. Do not wet or wipe it, and do not use tape.
  • Handle prints by the edges with clean, dry hands.
  • Place the print squarely against the guide mark, face down, and close the lid gently. Leave a few millimetres of margin so the edge of the picture is captured.

When not to use a scanner

Some originals should not go on glass. Photographs that are stuck together, cracked and flaking, curled, or mounted in a case (daguerreotypes, ambrotypes, tintypes) are at risk from pressure and can lose emulsion. Photograph them instead, following our guide to photographing an old photo with your phone. A print that is torn into pieces can be scanned, but lay the pieces together without overlap and do not tape them first.

Negatives and slides

A flatbed with a transparency lid or film holder can scan negatives, but a dedicated film scanner usually resolves more. Pre-1950s film on a cellulose nitrate base can decompose and is flammable; if a negative smells sharply acidic, has turned sticky or has gone yellow and brittle, do not scan it yourself. Contact a local archive or museum about safe handling. Safety film from later decades is fine to scan, though acetate film can develop a vinegar smell as it ages; keep that apart from other material.

Back up straight away

A scan is the first step in protecting a photo, not the last. Keep a master on your computer, a second copy on an external drive, and a third somewhere else, such as a cloud account or a drive at a relative's house. Then store the originals properly: our guide to storing and preserving old photographs covers that.

Common mistakes

  • Scanning at a low default setting such as 150 dpi, which looks fine on screen and prints badly.
  • Leaving scanner enhancements switched on, or cropping tight to the picture and losing the border.
  • Saving repeatedly as JPEG, which loses a little quality each time.
  • Scanning a copy of a copy. Always go back to the sharpest original you have.

With a clean scan in hand, restoring a family photo or a service portrait starts from the best possible base. If you want it in colour afterwards, see photo colourisation and how much of that is an informed guess.

Scan finished? Upload it for restoration, from $24 / £19 per photo, with free redos and a 30-day guarantee.

Restore my photo